DJI Air Unit + NewBeeDrone Infinity30 Stack

The NewBeeDrone Infinity30 Stack was designed to work seamlessly with DJI Digital FPV System. The DJI Air Unit only supports up to 4S battery. However, NewBeeDrone Infinity30 Stack will provide stable power (16W Output) to the DJI Air Unit (8W Total Consumption) to make it support up to 6S batteries. This combo includes the DJI Air Unit and NewBeeDrone Infinity 30 Stack -- with plug-and-play design to save time for a safe and clean build.

Specifications

Air Unit

• Input Power 7.4-17.6 V, about 4-9 W
• Operating Frequency: 5.725-5.850 GHz
• Transmitter Power (EIRP) FCC/SRRC: <30 dBm;
• CE: <14 dBm
• Min. Latency (end-to-end) Low Latency Mode (720p/120fps): <28 ms
• High Quality Mode (720p/60fps): <40 ms
• Max. Transmission Distance FCC/SRRC: <4 km; CE: <0.7 km
• Video Format MP4 (Video format: H.264; Audio format: ACC-LC)
• I/O Interface USB-C, MMCX, 3-in-1 port, microSD card slot
• Supported Flight Control System F3, F4, F7
• Operating Temperature Range 32°to 104°F (0° to 40°C)
• Weight: Air Unit (Camera included): 45.8 g
• Air Unit Dimensions: 44×37.8×14.4mm
• Camera Dimensions: 27.4×21.1×20.1mm
• Coaxial Cable Length: 100mm

Flight Controller

• MPU6000 Gyro
• STM32F405 CPUE @ 168mhz, can be overclocked
• 3-6S direct battery input
• 5V 2A,
• 9V 2A 18W Design for DJI FPV Air Unit
• 5V Camera Power
• betaflight OSD
• Flat bottom PCB for SUPER CLEAN builds
• Weight / Size: 8.36g/36x39 PCB with 30.5x30.5 mounting holes
• 6 UARTS. UART1 (INVERTER FOR SBUS),
• UART2 (FREE),
• UART3 (INVERTED TELEMETRY),
• UART4 (Free),
• UART5 (Smart Audio)
• UART6(Free)
• Built-in 4 IN 1 ESC socket(including ESC telemetry, External current sensor) JST1.0 8Pin
• Plug and plug with NBD Infinity30 ESC. Also compatible with most of the ESC on the market.
• Built-in solder pads for ESC signal output and power
• Printed layout instructions ON the board - no need for instructions!
• DJI FPV Air Unit socket (use UART1 and UART6)

Infinity 30 ESC

• LiPo Power input: 3S-6S
• ESC Programming: BLHeliSuite32
• Cont.Current: 40Ax4
• Burst Current: 55Ax4
• Weight / Size: 15.0g / 41x37.5x6mm
• Mounting holes: 30.5x30.5mm
• Signal plug JST1.0 8pin plug with NBD Infinity30FC
• Solder pad ready for signal and power.
• Heatsink design
• 10 Layer PCB with 2Oz Copper
• On board capacitor: 10uf x 48 Total 480uF, No need for external Capacitor
• BLHeli32 Programable Sided RGB LED x4
• Smoov performance design by Team NBD

DJI Air Unit Includes:

• 1x Camera
• 1x Air Unit Module
• 2x Air Unit Antenna (MMCX Elbow)
• 1x Coaxial Cable
• 1x Air Unit 3in1 Cable

NewBeeDrone Infinity 30 Stack Includes:

• 1x Infinity30 Flight Controller F4
• 1x Infinity30 4 in 1 ESC BLHeli32
• 4x Grommets
• 5x Nylon Screw
• 13x Nylon Lock nut
• 1x Infinity30 FC to DJI Air Unit Cable 50mm
• 1x Infinity30 FC to DJI Air Unit Cable 11mm
• 1x Infinity30 FC to DJI Air Unit Cable 16mm
• 1x Infinity30 FC to Infinity30 ESC cable 36mm