Long Range Systems LRS
Matek ELRS CRSF to SBUS converter
Remote Controllers → Long Range Systems LRS → ExpressLRS ELRS → Matek ELRS CRSF to SBUS converterSpecifications
Brand Name: MATEKSYS
Item Name: CRSF to SBUS Converter
Weight: 0.6g
Size: 15mm x 10mm (PCB)
Quantity: 2 Pcs
Compatible with CRSF/SBUS protocol receiver.
Support CRSF to SBUS, or SBUS to CRSF conversion
Battery voltage(RxBt) telemetry over CRSF protocol
CRSF to SBUS latency <7ms
Rated voltage: 4~5.5V @5V pad, 0~36V @VBAT pad
No 5V regulator built-in, VBAT pad is just for battery voltage sensing.
LED status:
slow blinks: CRSF-SBUS board doesn’t receive CRSF or SBUS signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART of CRSF-SBUS board.
solid ON: CRSF-SBUS board and receiver are working normally.
Tool: Matek Configurator
Firmwares: crsf_sbus_fw.zip
Mar.19,2022, v1.1.0: Fixed a failsafe bug when CRSF-SBUS converter can’t get CRSF signal from receiver.
Note:
Please update the CRSF-SBUS converter with firmware v1.1.0 when you receive the first batch of boards.
Upgrade CRSF-SBUS via A or B
A. USB-TTL modules, such as CP210x, FTDI
1. Wiring
TX1 — USB-TTL module RX
RX1 — USB-TTL module TX
5V — USB-TTL module 5V
G — USB-TTL module GND
2. Bridge the jumper pad at bottom side with a drop of tin, or bridge it with tips of tweezer when powering on.
3. Connect USB-TTL module to PC,
Blue LED on CRSF-SBUS board will blink fast, it means CRSF-SBUS board is working in boot mode.
now you can remove the jumper or remove it after flashing.
4. Open Matek configurator, Select COM port of USB-TTL, Baud rate 115200, Click “Connect”
5. OpenFile “crsf_sbus_vx.x.x.bin”
6. Click “Upgrade”
7. After update, remove the jumper.
B. INAV/BF serial passthrough
1. Wiring
TX1 — FC any spare UART_RX
RX1 — FC any spare UART_TX
5V — FC 5V or 4V5
G — FC GND
2. Bridge the jumper pad at bottom side with a drop of tin, or bridge it with tips of tweezer when powering on.
3. Connect FC USB to PC
Blue LED on CRSF-SBUS board will blink fast, it means CRSF-SBUS board is working in boot mode.
now you can remove the jumper or remove it after flashing.
4. open INAV/BF configurator, connect FC to configurator
5. click INAV/BF configurator “CLI” tab, type “serialpassthrough x 115200”, x = UART number -1, e.g. CRSF-SBUS board connect to FC UART4, type “serialpassthrough 3 115200”.
6. Disconnect FC from configurator, make sure USB is still plugged in FC and LED on CRSF-SBUS board is still blinking fast.
7. Open Matek configurator, Select COM port of Flight controler, Baud rate 115200, Click “Connect”
8. OpenFile “crsf_sbus_vx.x.x.bin”
9. Click “Upgrade”
10. After update, remove the jumper.
Package Included:
1 x CRSF to SBUS Converter
Prices for Matek ELRS CRSF to SBUS converter in stores
Deals found: 34 (ReadyMadeRC1, Banggood1, AliExpress1)
Store | Stock level | Lot price | Shipping cost | Coupon / promocode | Pcs./lot | 1pc price |
ReadyMadeRC | Out of stock | $6.99 | 2 | $3.5 | ||
Banggood | Out of stock | $13 | 2 | $6.5 | ||
AliExpress | High stock level | $42 | 1 | $42 |