Whoop Flight Controllers
Happymodel CrazybeeX V2.2 5in1 AIO F4 5A 5.8GHz 200mW PNP
Multirotors → Tinywhoops → Whoop Flight Controllers → Brushless Whoop FC → Happymodel CrazybeeX V2.2 5in1 AIO F4 5A 5.8GHz 200mW PNPCrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.
It's a better upgrade flight controller for your whoops.
- Use to build a 1-2S compatible lightest 65mm/75mm/85mm brushless whoop or 2-3 inch ultra light toothpick.
Specification:
Brand: Happymodel
Model: CrazybeeX FR/FS/PNP V2.2
Item Name: F4 Flight Controller AIO ESC VTX Receiver Board
Weight: 4.4g
Flight Controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) |
Onboard 5A 4In1 ESC | EFM8BB21 |
(CrazybeeX FR V2.2 Version) Onboard Frsky SPI Receiver | SPI BUS Receiver Frsky D8/D16 Compatible Channels: 8CH / 16CH |
(CrazybeeX FS V2.2 Version) Onboard Flysky SPI Receiver | SPI BUS Receiver |
(CrazybeeX PNP V2.2 Version W/O on Board Receiver) | No Onboard SPI Receiver |
Onboard 5.8G 40CH VTX | Output Power: 25mw~200mw switchable |
Onboard Voltage and Current detector | Voltage Meter scale “110” |
Features:
CrazybeeX FR V2.2 Bind procedure:
- Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn't blinking when binding with some new ACCESS firmware frsky radio , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .
CrazybeeX FS V2.2 Bind procedure:
- Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
SPI Receiver option:
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Futaba S-FHSS protocol
A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol
A7105_FLYSKY compatible with Flysky AFHDS protocol
Package Included:
1x CrazybeeX FR / FS / PNP V2.2 Version Flight Controller
1x Cale
1x bag of Screws & Standoffs
Prices for Happymodel CrazybeeX V2.2 5in1 AIO F4 5A 5.8GHz 200mW PNP in stores
Deals found: 23 ()