Holybro Kakute F7 HDV + Tekko32 F3 Metal 4in1 ESC 65A 6S for DJI FPV

The port to the DJI air unit on KAKUTE F7 HDV FC have been optimized, the output voltage has increased to 9V/2A.

Specification:

Brand Name: Holybro

Item Name: F7 Flight Controller & 65A BL_32 4in1 ESC Stack

Stack Height: 18mm

Mounting Hole: 30.5x30.5mm

Kakute F7 HDV Flight Controller ( Manual)

Input Voltage: 2-6S Lipo

MCU: STM32F745 32-bit processor

IMU: MPU6000

Barometer: BMP280

BEC Output: 5V 2A(max.) & 9V 2A

USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)

6 hardware UARTS (UART1,2,3,4,6,7)

All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.

- Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.

TF card for Blackbox logging

Dimensions: 35x35mm

Mounting Holes: Standard 30.5mm square to center of holes 

Weight: 8g

- Support DJI Air Unit

Flight Controller Features: 

- Supports Betaflight.

- High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.

- Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.

- Dedicated bootloader button for easy firmware flashing.

- Low-profile design fits into even very compact frames.

- Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).

- Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly      from the power supply.

- Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 9V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 9V output up to 2A to DJI FPV VTx.

- Supports BLHeli pass-through for easy ESC upgrade and configuration.

Tekko32 F3 Metal 4in1 ESC 65A ( Manual)

F3(M4 Core) 108Mhz MCU with BLHELI32 firmware

The 4in1 has onboard analog current sensor, and TLM function(then no current reading over TLM)

Uses metal case mosfet for better heat dissipation

No output BEC

Supports Lipo 4-6S

Extra capacitor needed for 6s (1000uf 35v for 6s usage.)

Dimensions:43 x 44mm

Mounting holes:30.5x30.5mm

Weight: 15.8g

The latest Tekko32F3 Metal 4in1 ESC has made various improvements on its performance compared to the previous version:

- Better optimized power path, providing a more stable performance.

- Doubled capacity of on-board capacitors, now capable of 2068uf.

- Amperage meter scale ratio has been adjusted to 168.

- The first blheli32 ESC in the market with default PWM output 96K giving you smoother and quieter experience.

- PCB with 3oz copper design, capable of handling bigger current, and better heat dissipation capacity,

  Enhanced and more robust Lipo input pad for soldering.

- The PCB design uses a design in which the drive circuit and the control circuit are separated.

- This design broadens the overcurrent capability of the drive circuit, and at the same time reduces the electrical interference to the control    circuit.

Package Included:

1x KAKUTE F7 HDV Flight Controller

1x 65A Tekko32F3 Metal 4in1 ESC

1x 1000uF 35V Electrolytic Capacitor

1x bag of Cables

1x bag of Screws