Lumenier LUX Mini F7 20x20 + 45A 6S 4in1 + 800mW VTX

The Lumenier F7 Mini Stack is the go-to 20x20 stack for all types of mini quads. The powerful F7 flight controller allows for simultaneous processes to be handled with ease, giving you a stable and clean signal to your sensors.

The 2-6S Mini Razor Pro 45A ESC features the latest gen. BLHeli_32 firmware running alongside an additional F3 processor to give you even more headroom. The Mini Razor Pro's innovative modular power system gives the user the option to install one of three different modules that give the 4-in-1 ESC additional functionality related to power management. Choose either the power filter module, extra capacitance module, or voltage regulator module to make your Mini Razor Pro fit to your specific needs (modules sold separately).

Tie it all together with a Smart Audio enabled VTX, capable of 5 variable transmitting powers from PIT, up to 800mW, this 20x20 stack will give any 30x30 stack a run for its money, and at a fraction of the size, weight, and cost!

LUX Mini F7

Features

• MCU: 216MHz STM32F722RET6
• IMU: ICM20602
• OSD: AB7456
• Blackbox: 128Mbit / 16MByte
• Anti-Vibration silicone grommets built-in
• 6x UARTs with built-in inversion
• 1x Softserial supported
• 1x I2C
• 1x SH1.0_8pin connector (Vbat/G/Curr/TLM/S1/S2/S3/S4)
• Vbat filtered output power for VTX
• Camera control
• Smartaudio & Tramp VTX protocol support
• WS2812 Led Strip support
• Beeper solder pad
• Input: 6~36V (2~8S LiPo)
• BEC: 5V 3A cont.
• LDO 3.3V: Max.200mA

Software/Hardware Features

• Betaflight support - target LUXMINIF7
• BLHeli passthrough flashing supported by hardware 

Specifications

• High quality, gold plated PCB
• Micro USB connector for programming
• Dimensions: 28x28x6mm (includes USB in height)
• Mounting Holes: 20mm square to center of holes 
• Weight: 5g

Razor ESC

Mini Razor Pro 45A

Features

• New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
• Latest Gen. firmware using BLHeli_32 (Razor_32 target)
• Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
• Modular Power System for even further customization (modules sold separately)
• Oversized motor pads for easy installation and maintenance
• Adaptive timing, compatible with a wide range of motors and Kv
• Synchronous rectification technology adds efficiency, damped light
• Powerful regenerative braking / active braking.
• 2-6s LiPo battery compatible

Customize your Mini Razor Pro even further with optional power modules.

Note: Modules sold separately.

Specs

• Input: 2-6s LiPoly
• Constant: 45 Amps
• Burst: 60 Amps
• Dimensions: 33x46x5mm
• Mounting holes: 20x20 M3
• Signal wire: 7cm
• Weight: 12.5g
  
• 8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4

LUX Mini VTX

The Lux Mini VTX comes with a whip antenna, but if you are looking for the best performance, upgrade to an AXII antenna listed in this bundle.

Features

• Compact 20x20 stackable design
• Variable power from 25mW to 800mW + Pit Mode
• Mounts with M3 or M2 hardware
• Conformal coated for added protection
• Licensed Smart Audio from TBS
• Optional protective cover included

Specifications

• Input Voltage: 7-36V DC
• Output Voltage: 5V 1A
• @12V Input Current: 40mA@Pitmode, 95mA@25mW, 185mA@200mW, 250mA@500mW, 380mA@800mW
• Channels: 48CH including RaceBand
• Power: PIT/25/200/500/800 mW
• Installation Hole: M3, (M2 with plastic cover) 20*20mm
• Dimensions: 28*28*3.3 mm
• Weight: 4.46g(without cover), 5.4g(with cover)

Downloads

• Download the User Manual for Lumenier LUX MINI F7 Flight Controller
• Download the LUX Mini VTX User Manual here